Impair Process Control

MITRE ATT&CK for ICS – Impair Process Control

1.Kravtext (engelskt original)#

The adversary is trying to manipulate, disable, or damage physical control processes.

Impair Process Control consists of techniques that adversaries use to disrupt control logic and cause determinantal effects to processes being controlled in the target environment. Targets of interest may include active procedures or parameters that manipulate the physical environment. These techniques can also include prevention or manipulation of reporting elements and control logic. If an adversary has modified process functionality, then they may also obfuscate the results, which are often self-revealing in their impact on the outcome of a product or the environment. The direct physical control these techniques exert may also threaten the safety of operators and downstream users, which can prompt response mechanisms. Adversaries may follow up with or use Inhibit Response Function techniques in tandem, to assist with the successful abuse of control processes to result in Impact.

T0806 – Brute Force I/O#

Adversaries may repetitively or successively change I/O point values to perform an action. Brute Force I/O may be achieved by changing either a range of I/O point values or a single point value repeatedly to manipulate a process function. The adversary’s goal and the information they have about the target environment will influence which of the options they choose. In the case of brute forcing a range of point values, the adversary may be able to achieve an impact without targeting a specific point. In the case where a single point is targeted, the adversary may be able to generate instability on the process function associated with that particular point.

Adversaries may use Brute Force I/O to cause failures within various industrial processes. These failures could be the result of wear on equipment or damage to downstream equipment.

T0836 – Modify Parameter#

Adversaries may modify parameters used to instruct industrial control system devices. These devices operate via programs that dictate how and when to perform actions based on such parameters. Such parameters can determine the extent to which an action is performed and may specify additional options. For example, a program on a control system device dictating motor processes may take a parameter defining the total number of seconds to run that motor.

An adversary can potentially modify these parameters to produce an outcome outside of what was intended by the operators. By modifying system and process critical parameters, the adversary may cause Impact to equipment and/or control processes. Modified parameters may be turned into dangerous, out-of-bounds, or unexpected values from typical operations. For example, specifying that a process run for more or less time than it should, or dictating an unusually high, low, or invalid value as a parameter.

T1692 – Unauthorized Message#

Adversaries may send unauthorized messages to ICS systems and devices to evade defenses or manipulate processes. Unauthorized messages can be categorized as either reporting messages that contain telemetry data about the current state of systems, devices, and processes or as command messages which instruct systems and devices on how to operate. By injecting unauthorized messages, adversaries can make it appear as if everything is working correctly when it isn’t, trigger alarms to misdirect personnel or impact processes, and manipulate controls to disrupt processes.(Citation: Bonnie Zhu, Anthony Joseph, Shankar Sastry 2011)

Adversaries may send unauthorized messages in an ICS environment using software found within the environment (living-off-the-land, vendor-specific interfaces, etc.), custom tooling leveraging OT protocols and libraries, or by positioning themselves between systems and devices and injecting messages into the communications such as the case with an Adversary-in-the-Middle attack.

T1692.001 – Command Message

Adversaries may send unauthorized command messages to instruct control system assets to perform actions outside of their intended functionality, or without the logical preconditions to trigger their expected function. Command messages are used in ICS networks to give direct instructions to control systems devices. If an adversary can send an unauthorized command message to a control system, then it can instruct the control systems device to perform an action outside the normal bounds of the device’s actions. An adversary could potentially instruct a control systems device to perform an action that will cause an Impact.(Citation: Bonnie Zhu, Anthony Joseph, Shankar Sastry 2011)

In the Dallas Siren incident, adversaries were able to send command messages to activate tornado alarm systems across the city without an impending tornado or other disaster.(Citation: Zack Whittaker April 2017)(Citation: Benjamin Freed March 2019)

T1692.002 – Reporting Message

Adversaries may spoof reporting messages in control system environments for evasion and to impair process control. In control systems, reporting messages contain telemetry data (e.g., I/O values) pertaining to the current state of equipment and the industrial process. Reporting messages are important for monitoring the normal operation of a system or identifying important events such as deviations from expected values.

If an adversary has the ability to Spoof Reporting Messages, they can impact the control system in many ways. The adversary can Spoof Reporting Messages that state that the process is operating normally, as a form of evasion. The adversary could also Spoof Reporting Messages to make the defenders and operators think that other errors are occurring in order to distract them from the actual source of a problem.(Citation: Bonnie Zhu, Anthony Joseph, Shankar Sastry 2011)

T1693 – Modify Firmware#

Firmware is low-level software embedded in hardware that enables systems and devices to function properly and is commonly found in ICS environments. Adversaries may modify firmware on a system or device by installing malicious or vulnerable versions that enable them to achieve objectives such as Persistence, Impair Process Control, and Inhibit Response Function.

Adversaries may modify system and device firmware by using the built-in firmware update functionality which may support local or remote installation. The malicious or vulnerable firmware may be delivered via Replication Through Removable Media, Supply Chain Compromise, or Remote Services. Once installed, the malicious or vulnerable firmware could be used to provide Rootkit and Hooking functionality, Exploitation for Privilege Escalation, or Denial of Service.(Citation: Basnight, Zachry, et al.)

T1693.001 – System Firmware

System firmware on modern assets is often designed with an update feature. Older device firmware may be factory installed and require special reprograming equipment. When available, the firmware update feature enables vendors to remotely patch bugs and perform upgrades. Device firmware updates are often delegated to the user and may be done using a software update package. It may also be possible to perform this task over the network.

An adversary may exploit the firmware update feature on accessible devices to upload malicious or out-of-date firmware. Malicious modification of device firmware may provide an adversary with root access to a device, given firmware is one of the lowest programming abstraction layers.(Citation: Basnight, Zachry, et al.)

T1693.002 – Module Firmware

Adversaries may install malicious or vulnerable firmware onto modular hardware devices. Control system devices often contain modular hardware devices. These devices may have their own set of firmware that is separate from the firmware of the main control system equipment.

This technique is similar to System Firmware, but is conducted on other system components that may not have the same capabilities or level of integrity checking. Although it results in a device re-image, malicious device firmware may provide persistent access to remaining devices.(Citation: Daniel Peck, Dale Peterson January 2009)

An easy point of access for an adversary is the Ethernet card, which may have its own CPU, RAM, and operating system. The adversary may attack and likely exploit the computer on an Ethernet card. Exploitation of the Ethernet card computer may enable the adversary to accomplish additional attacks, such as the following:(Citation: Daniel Peck, Dale Peterson January 2009)

Delayed Attack - The adversary may stage an attack in advance and choose when to launch it, such as at a particularly damaging time.
Brick the Ethernet Card - Malicious firmware may be programmed to result in an Ethernet card failure, requiring a factory return.
Random Attack or Failure - The adversary may load malicious firmware onto multiple field devices. Execution of an attack and the time it occurs is generated by a pseudo-random number generator.
A Field Device Worm - The adversary may choose to identify all field devices of the same model, with the end goal of performing a device-wide compromise.
Attack Other Cards on the Field Device - Although it is not the most important module in a field device, the Ethernet card is most accessible to the adversary and malware. Compromise of the Ethernet card may provide a more direct route to compromising other modules, such as the CPU module.